View MC10EP90_83913.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MC10EP90, MC100EP90 -3.3V / -5V Triple ECL Input to LVPECL/PECL Output Translator
The MC10/100EP90 is a TRIPLE ECL TO LVPECL/PECL translator. The device receives differential LVECL or ECL signals and translates them to differential LVPECL or PECL output signals. A VBB output is provided for interfacing with Single-Ended LVECL or ECL signals at the input. If a Single-Ended input is to be used the VBB output should be connected to the D input. The active signal would then drive the D input. When used the VBB output should be bypassed to ground by a 0.01 mF capacitor. The VBB output is designed to act as the switching reference for the EP90 under Single-Ended input switching conditions, as a result this pin can only source/sink up to 0.5 mA of current. To accomplish the level translation the EP90 requires three power rails. The VCC supply should be connected to the positive supply, and the VEE connected to the negative supply. The 100 Series contains temperature compensation.
http://onsemi.com
TSSOP-20 DT SUFFIX CASE 948E
MARKING DIAGRAM*
20 XXXX EP90 ALYW 1 xxx A L Y W = MC10 or 100 = Assembly Location = Wafer Lot = Year = Work Week
* 260 ps Typical Propagation Delay * Maximum Frequency > 3 GHz Typical * Voltage Supplies VCC = 3.0 V to 5.5 V, VEE = -3.0 V to -5.5 V, * * * * * *
GND = 0 V Open Input Default State Safety Clamp on Inputs Fully Differential Design Q Output Will Default LOW with Inputs Open or at VEE VBB Output These are Pb-Free Devices*
*For additional marking information, refer to Application Note AND8002/D.
ORDERING INFORMATION
See detailed ordering and shipping information in the package dimensions section on page 7 of this data sheet.
*For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D.
(c) Semiconductor Components Industries, LLC, 2004
1
June, 2004 - Rev. 4
Publication Order Number: MC10EP90/D
MC10EP90, MC100EP90
VCC 20 Q0 19 Q0 18 GND 17 Q1 16 Q1 15 GND 14 Q2 13 Q2 12 VCC 11
Table 1. PIN DESCRIPTION
PIN Q(0:2), Q(0:2) FUNCTION Differential LVPECL or PECL Outputs
D(0:2)*, D(0:2)* Differential LVECL or ECL Inputs LVPECL/ PECL LVPECL/ PECL LVPECL/ PECL VCC GND VEE VBB ECL ECL ECL Positive Supply Ground Negative Supply Output Reference Supply
* Pins will default LOW when left open.
Table 2. FUNCTION TABLE
1 VCC 2 D0 3 D0 4 VBB 5 D1 6 D1 7 VBB 8 D2 9 D2 10 VEE Function -5V ECL to 5V PECL -5V ECL to 3.3V PECL -3.3V ECL to 5V PECL -3.3V ECL to 3.3V PECL VCC 5V 3.3 V 5V 3.3 V GND 0V 0V 0V 0V VEE -5 V -5 V -3.3 V -3.3 V
Warning: All VCC, VEE and GND pins must be externally connected to Power Supply to guarantee proper operation.
Figure 1. TSSOP-20 (Top View) and Logic Diagram
Table 3. ATTRIBUTES
Characteristics Internal Input Pulldown Resistor Internal Input Pullup Resistor ESD Protection Human Body Model Machine Model Charged Device Model Value 75 kW N/A > 2 kV > 200 V > 2 kV Level 1 UL 94 V-0 @ 0.125 in 350 Devices
Moisture Sensitivity, Indefinite Time Out of Drypack (Note 1) Flammability Rating Transistor Count Meets or exceeds JEDEC Spec EIA/JESD78 IC Latchup Test 1. For additional information, refer to Application Note AND8003/D. Oxygen Index: 28 to 34
http://onsemi.com
2
MC10EP90, MC100EP90
Table 4. MAXIMUM RATINGS
Symbol VCC VEE VI Iout IBB TA Tstg qJA qJC Tsol Parameter PECL Mode Power Supply NECL Mode Power Supply PECL Mode Input Voltage NECL Mode Input Voltage Output Current VBB Sink/Source Operating Temperature Range Storage Temperature Range Thermal Resistance (Junction-to-Ambient) Thermal Resistance (Junction-to-Case) Wave Solder 0 lfpm 500 lfpm Standard Board <2 to 3 sec @ 248C TSSOP-20 TSSOP-20 TSSOP-20 Condition 1 GND = 0 V GND = 0 V GND = 0 V GND = 0 V Continuous Surge VI VCC VI VEE Condition 2 Rating 6 -6 6 -6 50 100 0.5 -40 to +85 -65 to +150 140 100 23 to 41 265 Units V V V V mA mA mA C C C/W C/W C/W C
Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected.
http://onsemi.com
3
MC10EP90, MC100EP90
Table 5. 10EP DC CHARACTERISTICS VCC = 3.3 V, VEE = -5.5 V to -3.0 V; GND = 0 V (Note 2)
-40C Symbol IEE ICC VOH VOL VIH VIL VBB VIHCMR IIH IIL Characteristic Negative Power Supply Current Positive Power Supply Current Output HIGH Voltage (Note 3) Output LOW Voltage (Note 3) Input HIGH Voltage (Single-Ended) Input LOW Voltage (Single-Ended) Output Voltage Reference Input HIGH Voltage Common Mode Range (Differential) (Note 4) Input HIGH Current Input LOW Current 0.5 Min 5 43 2165 1365 -1210 -1935 -1510 -1410 Typ 13 55 2290 1490 Max 20 67 2415 1615 -885 -1610 -1310 0.0 150 0.5 Min 5 43 2230 1430 -1145 -1870 -1445 -1345 25C Typ 13 55 2355 1555 Max 20 67 2480 1680 -820 -1545 -1245 0.0 150 0.5 Min 5 43 2290 1490 -1085 -1810 -1385 -1285 85C Typ 13 55 2415 1615 Max 20 67 2540 1740 -760 -1485 -1185 0.0 150 Unit mA mA mV mV mV mV mV V mA mA
VEE+2.0
VEE+2.0
VEE+2.0
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 2. Input and output parameters vary 1:1 with VCC. 3. All loading with 50 W to VCC - 2.0 V. 4. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal.
Table 6. 10EP DC CHARACTERISTICS VCC = 5.0 V, VEE = -5.5 V to -3.0 V; GND = 0 V (Note 5)
-40C Symbol IEE ICC VOH VOL VIH VIL VBB VIHCMR IIH IIL Characteristic Negative Power Supply Current Positive Power Supply Current Output HIGH Voltage (Note 6) Output LOW Voltage (Note 6) Input HIGH Voltage (Single-Ended) Input LOW Voltage (Single-Ended) Output Voltage Reference Input HIGH Voltage Common Mode Range (Differential) (Note 7) Input HIGH Current Input LOW Current 0.5 Min 5 43 3865 3065 -1210 -1935 -1510 -1410 Typ 13 55 3990 3190 Max 20 67 4115 3315 -885 -1610 -1310 0.0 150 0.5 Min 5 43 3930 3130 -1145 -1870 -1445 -1345 25C Typ 13 55 4055 3255 Max 20 67 4180 3380 -820 -1545 -1245 0.0 150 0.5 Min 5 43 3990 3190 -1085 -1810 -1385 -1285 85C Typ 13 55 4115 3315 Max 20 67 4240 3440 -760 -1485 -1185 0.0 150 Unit mA mA mV mV mV mV mV V mA mA
VEE+2.0
VEE+2.0
VEE+2.0
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 5. Input and output parameters vary 1:1 with VCC. 6. All loading with 50 W to VCC - 2.0 V. 7. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal.
http://onsemi.com
4
MC10EP90, MC100EP90
100EP DC CHARACTERISTICS VCC = 3.3 V, VEE = -5.5 V to -3.0 V; GND = 0 V (Note 8)
-40C Symbol IEE ICC VOH VOL VIH VIL VBB VIHCMR IIH IIL Characteristic Negative Power Supply Current Positive Power Supply Current Output HIGH Voltage (Note 9) Output LOW Voltage (Note 9) Input HIGH Voltage (Single-Ended) Input LOW Voltage (Single-Ended) Output Voltage Reference Input HIGH Voltage Common Mode Range (Differential) (Note 10) Input HIGH Current Input LOW Current 0.5 Min 5 45 2155 1355 -1210 -1935 -1525 -1425 Typ 13 58 2280 1480 Max 20 70 2405 1605 -885 -1610 -1325 0.0 150 0.5 Min 5 50 2155 1355 -1145 -1870 -1525 -1425 25C Typ 13 62 2280 1480 Max 20 75 2405 1605 -820 -1545 -1325 0.0 150 0.5 Min 5 53 2155 1355 -1085 -1810 -1525 -1425 85C Typ 13 65 2280 1480 Max 20 78 2405 1605 -760 -1485 -1325 0.0 150 Unit mA mA mV mV mV mV mV V mA mA
VEE+2.0
VEE+2.0
VEE+2.0
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 8. Input and output parameters vary 1:1 with VCC. 9. All loading with 50 W to VCC - 2.0 V. 10. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal.
100EP DC CHARACTERISTICS VCC = 5.0 V, VEE = -5.5 V to -3.0 V; GND = 0 V (Note 11)
-40C Symbol IEE ICC VOH VOL VIH VIL VBB VIHCMR IIH IIL Characteristic Negative Power Supply Current Positive Power Supply Current Output HIGH Voltage (Note 12) Output LOW Voltage (Note 12) Input HIGH Voltage (Single-Ended) Input LOW Voltage (Single-Ended) Output Voltage Reference Input HIGH Voltage Common Mode Range (Differential) (Note 13) Input HIGH Current Input LOW Current 0.5 Min 5 45 3855 3055 -1210 -1935 -1525 -1425 Typ 13 58 3980 3180 Max 20 70 4105 3305 -885 -1610 -1325 0.0 150 0.5 Min 5 50 3855 3055 -1145 -1870 -1525 -1425 25C Typ 13 62 3980 3180 Max 20 75 4105 3305 -820 -1545 -1325 0.0 150 0.5 Min 5 53 3855 3055 -1085 -1810 -1525 -1425 85C Typ 13 65 3980 3180 Max 20 78 4105 3305 -760 -1485 -1325 0.0 150 Unit mA mA mV mV mV mV mV V mA mA
VEE+2.0
VEE+2.0
VEE+2.0
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 11. Input and output parameters vary 1:1 with VCC. 12. All loading with 50 W to VCC - 2.0 V. 13. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC.. The VIHCMR range is referenced to the most positive side of the differential input signal.
http://onsemi.com
5
MC10EP90, MC100EP90
Table 7. AC CHARACTERISTICS VEE = -3.0 V to -5.5 V; VCC = 3.0 V to 5.5 V; GND = 0 V (Note 14)
-40C Symbol fmax tPLH, tPHL tSKEW Characteristic Maximum Frequency (See Figure 2 Fmax/JITTER) Propagation Delay to Output Differential Duty Cycle Skew (Note 15) Within Device Skew Q, Q Device to Device Skew (Note 15) tJITTER VPP tr tf Cycle-to-Cycle Jitter (See Figure 2 Fmax/JITTER) Input Voltage Swing (Differential Configuration) Output Rise/Fall Times (20% - 80%) Q, Q 150 70 0.2 800 120 170 Min Typ >3 240 5.0 310 20 80 140 <1 1200 170 150 80 0.2 800 130 200 Max Min 25C Typ >3 260 5.0 340 20 80 140 <1 1200 180 150 100 0.2 800 150 230 Max Min 85C Typ >3 300 5.0 370 20 80 140 <1 1200 230 ps mV ps Max Unit GHz ps ps
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 14. Measured using a 750 mV source, 50% duty cycle clock source. All loading with 50 W to VCC-2.0 V. 15. Skew is measured between outputs under identical transitions. Duty cycle skew is defined only for differential operation when the delays are measured from the cross point of the inputs to the cross point of the outputs.
900 800 VOUTpp (mV) 700 600 500 400 300 200
9 JITTEROUT ps (RMS) 8 7 6 5 4 3 2 (JITTER) 4000 1 5000
EEEEEEEEEEE EEEEEEEEEEE
0 0 1000 2000 6
100
3000
FREQUENCY (MHz)
Figure 2. Fmax/Jitter
http://onsemi.com
EE EE
MC10EP90, MC100EP90
Zo = 50 W
Q Driver Device Q
D Receiver Device
Zo = 50 W 50 W 50 W
D
VTT VTT = VCC - 2.0 V
Figure 3. Typical Termination for Output Driver and Device Evaluation (See Application Note AND8020/D - Termination of ECL Logic Devices.)
ORDERING INFORMATION
Device MC10EP90DT MC10EP90DTR2 MC100EP90DT MC100EP90DTR2 Package TSSOP-20 TSSOP-20 TSSOP-20 TSSOP-20 Shipping 75 Units / Rail 2500 / Tape & Rail 75 Units / Rail 2500 / Tape & Rail
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.
Resource Reference of Application Notes
AN1405/D AN1406/D AN1503/D AN1504/D AN1568/D AN1642/D AND8001/D AND8002/D AND8020/D AND8066/D AND8090/D - ECL Clock Distribution Techniques - Designing with PECL (ECL at +5.0 V) - ECLinPSt I/O SPiCE Modeling Kit - Metastability and the ECLinPS Family - Interfacing Between LVDS and ECL - The ECL Translator Guide - Odd Number Counters Design - Marking and Date Codes - Termination of ECL Logic Devices - Interfacing with ECLinPS - AC Characteristics of ECL Devices
http://onsemi.com
7
MC10EP90, MC100EP90
PACKAGE DIMENSIONS
TSSOP-20 DT SUFFIX PLASTIC TSSOP PACKAGE CASE 948E-02 ISSUE B
20X
K REF
M
0.15 (0.006) T U
S
0.10 (0.004)
TU
S
V
S
2X
L/2
20
11
B L
PIN 1 IDENT 1 10
-U-
0.15 (0.006) T U
S
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE -W-. MILLIMETERS MIN MAX 6.40 6.60 4.30 4.50 --- 1.20 0.05 0.15 0.50 0.75 0.65 BSC 0.27 0.37 0.09 0.20 0.09 0.16 0.19 0.30 0.19 0.25 6.40 BSC 0_ 8_ INCHES MIN MAX 0.252 0.260 0.169 0.177 --- 0.047 0.002 0.006 0.020 0.030 0.026 BSC 0.011 0.015 0.004 0.008 0.004 0.006 0.007 0.012 0.007 0.010 0.252 BSC 0_ 8_
A -V-
C D 0.100 (0.004) -T- SEATING
PLANE
-W- G
H
DETAIL E
DIM A B C D F G H J J1 K K1 L M
ECLinPS is a trademark of Semiconductor Components INdustries, LLC (SCILLC).
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center 2-9-1 Kamimeguro, Meguro-ku, Tokyo, Japan 153-0051 Phone: 81-3-5773-3850 ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder For additional information, please contact your local Sales Representative.
http://onsemi.com
8
MC10EP90/D

▲Up To Search▲

Price & Availability of MC10EP90

	To Download MC10EP90 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .